|
|
> Edit Configuration <
|
The configuration file is named CONFIG.TXT. Download
the configuration file (right-click and select "Save link
as"),
then open and edit it directly with a text editor.
The following describes each configuration parameter in
detail: |
|
[SETTINGS]
TimeZone=+00:00
MotionDetectionMode=OFF
* Default settings |
|
TimeZone=+00:00
Available options: -12:00, -11:00, -10:00, -09:30, -09:00, -08:00,
-07:00,-06:00, -05:00, -04:30, -04:00, -03:30, -03:00,
-02:30, -02:00, -01:00, +00:00,
+01:00, +02:00, +03:00, +00:00 03:30, +04:00, +04:30,
+05:00, +05:30, +05:45, +06:00, +06:30, +07:00, +08:00,
+08:45, +09:00, +09:30, +10:00, +10:30, +11:00, +11:30,
+12:00, +12:45, +13:00, +13:45, +14:00 |
|
• MotionDetectionMode <Motion Detection Mode> |
|
MotionDetectionMode=OFF
Available options: OFF / H / M / L |
|
OFF: Disables Motion Detection Mode.
H: High
sensitivity
Suitable for large objects such as vehicles that remain
relatively still when stopped. When a vehicle is stationary,
there is little vibration, and acceleration changes are
relatively smooth when it starts moving. Setting the
sensitivity to H allows the device to quickly detect
movement and wake up automatically.
M: Medium sensitivity
Suitable for detecting movement of large animals such as
horses, cattle, and sheep. After the subject enters a
resting state, slight movement may occur even though it has
not actually started moving. Setting the sensitivity to M
helps prevent the device from waking up due to minor
movement and reduces false triggers.
L: Low sensitivity
Suitable for detecting movement of animals such as cats,
dogs, and large birds. After the subject enters a resting
state, frequent and brief movements may occur even though it
has not actually started moving. Setting the sensitivity to
L allows the device to wake up only when movement is
sufficiently strong and sustained, further reducing false
triggers.
When Motion Detection Mode is
enabled, the device automatically enters sleep mode after
remaining stationary for more than 1 minute, and the Status Indicator flashes at
intervals. When movement is detected and its intensity and
duration exceed the set thresholds, the device automatically
wakes up and resumes recording.
 |
Sleeping (flashes every 10 seconds) |
Note:
Motion Detection Mode cannot be enabled when Scheduled
Recording is enabled (Schedule=ON). |
|
[RECORD]
Format=FUSION
Fusion=GNSS
LogMode=1Hz
SpeedMask=1km
OneTrackPerDay=OFF
* Default settings |
|
Format=FUSION
Available options: FUSION / CSV / GPX /
NMEA |
|
FUSION: Stores tracks in FUSION format.
CSV: Stores tracks in CSV format, the same format used by
P-1, P-1M2, and P-10.
GPX: Stores tracks in GPX format. GPS Exchange Format
is a common file format for storing and exchanging GPS
tracks, waypoints, and routes.
NMEA: Stores tracks in NMEA format. National Marine
Electronics Association is a common text format for storing
and transmitting GNSS positioning data. |
|
• Fusion <Recording Content (FUSION Only)> |
|
Fusion=GNSS
Available options: GNSS / GNSS+IMU / IMU |
|
GNSS: Records GNSS data only.
GNSS+IMU: Records GNSS data and acceleration data.
IMU: Records acceleration data only. |
|
• LogMode <Recording Mode> |
|
LogMode=1Hz
Continuous Recording Mode
Available options:
|
Update Rate |
1Hz
|
|
Distance Interval (Metric) |
5m / 10m / 20m / 50m / 100m
|
|
Distance Interval (Imperial) |
20ft / 50ft / 100ft / 200ft / 500ft
|
|
Time Interval |
5s / 10s
|
Interval Recording Mode
Available options:
|
Time Interval (> 1 minute) |
1min - 59min / 1h -24h |
|
|
In Continuous Recording Mode,
for example, with LogMode=100m, the device remains
powered on and records one track point every 100 meters.
In Interval Recording Mode, for example, with
LogMode=1min, the device automatically wakes up every 1
minute, records one track point, then enters sleep mode.
This cycle repeats continuously. |
|
• SpeedMask <Trigger Speed> |
|
SpeedMask=1km
Available range: OFF / 1km - 200km / 1 -
200mi |
|
OFF：Disabled
1km: Records only track points when the speed exceeds 1
km/h.
A minimum setting of 1km is recommended. When the device is
stationary, it stops recording, which can significantly
reduce redundant data and save storage space.
When the device is used in an environment with limited sky
visibility or where GNSS signals are easily obstructed,
increasing this value, for example to 1km–5km, can
help reduce track drift. |
|
• OneTrackPerDay <One Track Per Day> |
|
OneTrackPerDay=OFF
Available options: OFF / ON |
|
OFF: Creates a new track file each
time the device is powered on.
ON: Creates only one track file per day. |
|
[SCHEDULE]
Schedule=OFF
Wake=08:00
Duration=00:10
* Default settings |
|
• Schedule <Scheduled Recording> |
|
Schedule=OFF
Available options: OFF / ON |
|
OFF: Disables Scheduled Recording.
ON: Enables Scheduled Recording. |
|
Wake=08:00
Available range: 00:00 - 23:59 |
|
Sets the time when the device
automatically wakes up each day. For example, 08:00 means
the device wakes up automatically at 8:00 AM every
day. |
|
• Duration <Recording Duration> |
|
Duration=00:10
Available range: 00:00 - 23:59 |
|
Sets how long the device remains
active after waking up. For example, 00:10 means the device
operates continuously for 10 minutes after waking up,
then enters sleep mode.
Note:
After a warm start, the device typically takes about 1
minute to acquire a fix. To ensure reliable positioning and
data recording, a recording duration of at least 2 minutes
is recommended. Set Duration=00:02. |
|
[SCHEDULE]
Schedule=OFF
Wake=08:00
Duration=00:10
| <------- |
|
The line break at the end of the configuration file must be
preserved. Do not delete it, as this may prevent the
configuration file from being recognized correctly. |
|
|
|
